- Service ▼
- Products ▼
✨ 20+ Years Experience | 5,000+ Global Brands All Products →
- Sustainability
- About Us ▼
- Related Resources ▼
- Contact Us
AQL for Packaging: How to Inspect a Custom Box Order Before It Ships
In brief: for custom paper packaging, use AQL 2.5 at General Inspection Level II for major defects and AQL 0 for critical ones. On a 1,200–3,200 piece order that means inspecting 125 pieces and rejecting the lot at 8 major defects. Packaging fails on print registration, board calliper, glue lines and colour drift far more often than on structural collapse — so write the defect list around those, not around generic quality language.
01 Most AQL plans for packaging are never used
Buyers routinely paste “AQL 2.5, level II” into a purchase order without checking what it means for their actual quantity. Then the shipment arrives, something is wrong, and nobody can say whether it passed or failed, because nobody sampled.
The plan only works if three numbers are fixed before production:
- The sample size — how many boxes get pulled from the lot.
- The accept number — how many defects are tolerated before the lot is rejected.
- The defect definition — what counts as a defect at all.
Numbers one and two come from a standard table. Number three is the one that actually decides whether your inspection is useful, and it is the one almost nobody writes down.
02 Sample sizes for a real packaging order
Custom packaging lots are usually between 500 and 50,000 pieces, so the practical range is narrow. Below are the figures from ISO 2859-1, single sampling, General Inspection Level II — the level used by default on most consumer goods.
| Lot size (pieces) | Sample size | AQL 1.0 Accept / Reject | AQL 2.5 Accept / Reject | AQL 4.0 Accept / Reject |
|---|---|---|---|---|
| 501 – 1,200 | 80 | 2 / 3 | 5 / 6 | 7 / 8 |
| 1,201 – 3,200 | 125 | 3 / 4 | 7 / 8 | 10 / 11 |
| 3,201 – 10,000 | 200 | 5 / 6 | 10 / 11 | 14 / 15 |
| 10,001 – 35,000 | 315 | 7 / 8 | 14 / 15 | 21 / 22 |
Read it like this: a 2,000-piece order at AQL 2.5, level II, means you inspect 125 boxes. If you find 7 or fewer major defects, the lot passes. At 8, it fails.
Two things surprise buyers at this point. First, the sample size does not scale with the order — a 500-piece order and a 1,000-piece order both sample 80 pieces. Second, a failing lot is not a rejection of the whole shipment. It means the supplier has to sort, rework or replace, and you inspect again.
03 Which inspection level to use
| Level | Sample size relative to II | When to use it |
|---|---|---|
| Level I | About 40% | Repeat orders from a supplier with a clean history |
| Level II | Baseline | Default for custom packaging. Use this unless you have a reason not to. |
| Level III | About 160% | First order, new supplier, or a box where a defect is expensive downstream |
| Tightened | Level II, stricter limits | Applied after two consecutive lots fail |
If this is your first order with a factory, use Level III for the first run and Level II afterwards. The extra sampling costs almost nothing on a paper box order and catches a process that is not yet stable.
04 Defect classification for paper packaging
This is where generic AQL templates fail. A “critical defect” on a food product is a foreign body. On a printed box, it is something else entirely.
| Class | Definition for paper packaging | Typical AQL |
|---|---|---|
| Critical | Unusable or unsafe: wrong dimensions beyond tolerance, wrong material grade, missing print on the front panel, box will not close, contamination, sharp exposed edge | 0 |
| Major | Functionally acceptable but clearly not what was approved: colour outside the agreed tolerance, print misregistration visible at arm’s length, delamination, glue failure, wrong finishing | 2.5 |
| Minor | Cosmetic and only visible on close inspection: light scuffing, small glue squeeze-out, slight board warp, faint machine marks | 4.0 |
Write the definitions in physical terms, not adjectives. “Colour outside tolerance” is unusable in an inspection; “ΔE above 2.0 against the approved sample” is not.
05 What actually goes wrong on a paper box order
From production data on printed carton and rigid box runs, these are the defect categories that show up, roughly in order of frequency:
| Defect | Class | Root cause | How to check |
|---|---|---|---|
| Colour drift between cartons | Major | Separate print runs or ink batches | Compare the first and last carton of the lot side by side under the same light |
| Print misregistration | Major | Press setup, paper stretch | Look at the overlap on a two-colour edge; more than 0.2 mm is visible |
| Board calliper under spec | Critical | Supplier substituted a lighter grade | Micrometer on ten random boxes; compare to the approved sample |
| Glue line failure | Critical | Insufficient adhesive, cold glue line | Open and close each sampled box; pull the side seam |
| Lamination delamination | Major | Film tension or heat | Try to lift the film at a corner |
| Scuffing in transit | Minor | Cartons packed too tightly, no interleaving | Check the outer cartons, not just the boxes |
| Dimension drift | Critical | Die wear or board moisture | Measure length, width and depth on five boxes |
Colour drift is the single most common cause of a failed packaging inspection, and it is the hardest to resolve after the fact, because there is no fix other than reprinting. This is why the approved sample has to be signed and retained by both sides before the run starts.
06 Three points in the process, three different inspections
| Inspection | When | What it catches |
|---|---|---|
| Pre-production | Before the run starts | Material grade, die condition, ink match, approved sample on hand |
| During production (DUPRO) | At 20–30% of the run | Process drift — the expensive defects, caught while they are still fixable |
| Pre-shipment (PSI) | When the lot is packed, before loading | Whether the finished goods match the approved sample |
Most buyers only book a pre-shipment inspection. That is also the least useful one on its own: by the time the boxes are packed, a colour problem is already 20,000 boxes deep. A DUPRO inspection at 25% of the run costs about the same and catches the problem while the press is still running.
07 How to write the inspection instruction
An inspection agency will inspect whatever you tell them, which means a vague instruction produces a vague report. Cover these six points:
- Which lot, which PO, how many pieces. Inspectors need the exact lot to sample from.
- Sample size and AQL for each defect class. Critical 0, major 2.5, minor 4.0 is a reasonable default.
- The approved sample. Physical reference, signed and dated. Without it, colour cannot be judged.
- Tolerance table. Allowed ± on length, width, depth, and board calliper.
- Defect list in physical terms, with photographs of what a pass and a fail look like.
- Where the report goes and who can approve rework. A report with no decision-maker wastes the inspection.
If you are buying from China and want the wider context around inspections, inspections sit between how to buy custom boxes from China and how the goods get loaded.
08 When the lot fails
A failed lot is a process event, not a negotiation. The practical sequence:
- The supplier sorts 100%. Every piece is checked, defective pieces are removed, good pieces are re-packed.
- You inspect the sorted lot again, at the same level.
- Decide on the defects. Minor defects are usually accepted with a price adjustment. Major defects are reworked or replaced. Critical defects are rejected outright.
- Record what failed and why. If the same defect appears on the next lot, the supplier applies tightened inspection — that is the mechanism the standard is designed around.
The commercial side of this is worth understanding before it happens: a failed inspection is usually cheaper than a reprint, and much cheaper than a recalled shipment. What is expensive is discovering the problem at your warehouse. See what actually drives the cost of custom packaging for where inspection and rework sit in the unit price.
Need the quality documentation for your order?
We run internal AQL checks at pre-production, mid-run and pre-shipment, and we supply the inspection records with the shipment. Send your specification and we will show you what the report looks like for your box.
Request a quoteFrequently asked questions
What AQL should I use for custom packaging?
AQL 2.5 at General Inspection Level II is the practical default for printed paper packaging, with AQL 0 for critical defects. On a 1,200–3,200 piece order that means inspecting 125 pieces and rejecting the lot at 8 major defects.
How many pieces are inspected on a 1,000-piece order?
80 pieces at Level II. Sample size is set by the lot size band, not by the exact quantity — a 501-piece order and a 1,200-piece order both sample 80.
What counts as a critical defect on a printed box?
Anything that makes the box unusable or unsafe: wrong dimensions beyond tolerance, a substituted board grade, missing print on the front panel, a box that will not close, contamination, or a sharp exposed edge. Critical defects are set to AQL 0, meaning any occurrence is a fail.
What is the difference between Level I, II and III?
Level II is the default sample size. Level I samples roughly 40% of that and is used for repeat orders from a proven supplier. Level III samples about 160% and is used for first orders, new suppliers, or boxes where a defect is expensive downstream.
Should I inspect during production or only before shipment?
Both, if the order is large. A pre-shipment inspection tells you the lot is wrong when it is already too late to fix cheaply. A during-production check at 20–30% of the run catches process drift while the press is still running.
What is the most common reason a packaging inspection fails?
Colour drift between cartons, usually caused by separate print runs or different ink batches. It is the most common failure and the hardest to fix after the fact, which is why a signed approved sample has to exist before production starts.
Who pays for the inspection?
The buyer, in a standard pre-shipment inspection arrangement — typically a few hundred dollars for a third-party agency visit. On a 20,000-piece order that is a small fraction of the unit cost, and cheaper than a reprint.
Do you provide your own inspection reports?
Yes. We run internal checks at pre-production, mid-run and pre-shipment, and the records ship with the goods. Third-party inspection is also welcome — we schedule the lot so an agency can sample before loading.
What tolerance should I set on box dimensions?
For folding cartons, ±1 mm on each dimension is standard. For rigid boxes, ±1.5 mm on the lid and base fit, with the lid sitting 1–1.5 mm proud of the base on the reveal. Tighter than that is possible but moves you into a higher cost band.
Can I inspect a small order?
Yes, but the economics change. A third-party inspection on a 500-piece order can cost more per unit than the box itself. For orders under roughly 2,000 pieces, ask the factory for their internal inspection records instead, and check a sample yourself on arrival.
Read next
- How to buy custom boxes from China
- How to find a packaging manufacturer you can trust
- What information you need to customise packaging
- What actually drives the cost of custom packaging
- Our manufacturing capabilities and the equipment behind them
- The buyer profiles we work with
- Frequently asked questions about working with us
